#!/bin/bash # ============================================================================= # WireGuard Client Autoconnect Installer for Flint4 # For Debian/Ubuntu systems connecting to Flint4 router at twy4us.duckdns.org # ============================================================================= set -euo pipefail RED='\033[0;31m' GREEN='\033[0;32m' YELLOW='\033[1;33m' BLUE='\033[0;34m' NC='\033[0m' TUNNEL_NAME="wgclient2" PEER_HOST="twy4us.duckdns.org" CONFIG_DIR="/etc/wireguard" CONFIG_FILE="${CONFIG_DIR}/${TUNNEL_NAME}.conf" SERVICE_NAME="wg-${TUNNEL_NAME}" info() { echo -e "${BLUE}[INFO]${NC} $1"; } success() { echo -e "${GREEN}[SUCCESS]${NC} $1"; } warn() { echo -e "${YELLOW}[WARN]${NC} $1"; } error() { echo -e "${RED}[ERROR]${NC} $1"; } if [[ $EUID -ne 0 ]]; then error "This script must be run as root (use sudo)" exit 1 fi if ! command -v apt-get &>/dev/null; then error "This script is for Debian/Ubuntu systems only" exit 1 fi # Step 1: Install WireGuard info "Checking for WireGuard installation..." if ! command -v wg &>/dev/null; then info "Installing WireGuard..." apt-get update -qq apt-get install -y -qq wireguard wireguard-tools success "WireGuard installed" else success "WireGuard already installed" fi # Step 2: Get config file path echo "" echo -e "${BLUE}========================================${NC}" echo -e "${BLUE} WireGuard Client Installer${NC}" echo -e "${BLUE}========================================${NC}" echo "This script will set up a WireGuard client tunnel '${TUNNEL_NAME}'" echo "to connect to: ${PEER_HOST}" echo "" read -rp "Enter the path to your WireGuard config file (e.g., /root/wg0.conf, ~/wireguard.conf): " CONFIG_SOURCE CONFIG_SOURCE="${CONFIG_SOURCE/#\~/$HOME}" if [[ ! -f "$CONFIG_SOURCE" ]]; then error "Config file not found: $CONFIG_SOURCE" exit 1 fi if ! grep -q "\[Interface\]" "$CONFIG_SOURCE" || ! grep -q "\[Peer\]" "$CONFIG_SOURCE"; then error "Invalid WireGuard config (missing [Interface] or [Peer] section)" exit 1 fi success "Config file verified: $CONFIG_SOURCE" # Step 3: Install config info "Installing config to ${CONFIG_FILE}..." mkdir -p "$CONFIG_DIR" cp "$CONFIG_SOURCE" "$CONFIG_FILE" chmod 600 "$CONFIG_FILE" success "Config installed" # Step 4: Create systemd service info "Creating systemd service..." cat > /etc/systemd/system/${SERVICE_NAME}.service << EOF [Unit] Description=WireGuard via wg-quick(8) for ${TUNNEL_NAME} After=network-online.target Wants=network-online.target [Service] Type=oneshot RemainAfterExit=yes ExecStart=/usr/bin/wg-quick up ${TUNNEL_NAME} ExecStop=/usr/bin/wg-quick down ${TUNNEL_NAME} Restart=on-failure RestartSec=5 [Install] WantedBy=multi-user.target EOF systemctl daemon-reload systemctl enable "${SERVICE_NAME}" success "Service created and enabled for boot" # Step 5: Start the tunnel info "Starting WireGuard tunnel..." wg-quick up "$TUNNEL_NAME" success "Tunnel is UP" # Step 6: Verify sleep 2 if ip link show "$TUNNEL_NAME" &>/dev/null; then success "Interface ${TUNNEL_NAME} is active" echo "" echo "Tunnel details:" ip addr show "$TUNNEL_NAME" echo "" echo "WireGuard status:" wg show "$TUNNEL_NAME" else error "Interface not found. Check config and run: wg-quick up ${TUNNEL_NAME}" exit 1 fi # Summary echo "" echo -e "${GREEN}========================================${NC}" echo -e "${GREEN} WireGuard Client Setup Complete!${NC}" echo -e "${GREEN}========================================${NC}" echo "" echo "Tunnel: ${TUNNEL_NAME}" echo "Peer: ${PEER_HOST}" echo "Config: ${CONFIG_FILE}" echo "Service: ${SERVICE_NAME}" echo "" echo "Commands:" echo " wg-quick up ${TUNNEL_NAME} - Bring up" echo " wg-quick down ${TUNNEL_NAME} - Bring down" echo " wg show ${TUNNEL_NAME} - Show status" echo " systemctl status ${SERVICE_NAME} - Service status" echo "" echo -e "${GREEN}Tunnel starts automatically on boot.${NC}"